Plumbing Valves

Prestex

Chromium plated brass full bore ball valve (yellow "T" handle). Compression ends to EN 1254/2.CE

Chromium plated brass full bore ball valve (yellow "T" handle). Compression ends to EN 1254/2.CE

SizePattern No.Pack 1 QtyPack 2 QtyCodeBarcodePrice (£) ex VAT
15mmPB300T10805013866037290£17.23
22mmPB300T10405013866037306£22.82
28mmPB300T5205013866037313£32.29
CodeDescriptionABC
25502115MM PB300T BRASS BALL VALVE CXC YELLOW7742500.220
25502222MM PB300T BRASS BALL VALVE CXC YELLOW8554600.386
25502328MM PB300T BRASS BALL VALVE CXC YELLOW10057600.561
Pegler Yorkshire reserve the right to change specifications
This is an image that shows the dimensions of the product
SizePattern No.CodeIndividual Weight (kg)Pack 1 Weight (kg)Pack 2 Weight (kg)
15mmPB300T2550210.252.5420.45
22mmPB300T2550220.414.2416.95
28mmPB300T2550230.663.3713.48
SizePattern No.CodeKv m3/h
15mmPB300T25502117.00
22mmPB300T25502241.00
28mmPB300T25502370.00
Pegler Yorkshire reserve the right to change specifications

Valves and Fittings

Pegler Yorkshire Customcare 5 Year Guarantee - Terms and Conditions

Products are subject to a 5 year guarantee that is between Pegler Yorkshire and the final purchaser of the product.

The guarantee is subject to proof of purchase being supplied.

This guarantee does not affect any statutory rights the consumer may have in law.

The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear and tear.

This product range has been designed for the use of homeowners, domestic and commercial applications and therefore the guarantee is subject to the product being properly selected for their intended service conditions.

The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting instructions.

This is reinforced where valves are covered by the European Pressure Equipment Directive (PED97/23/EC) where Installation, Operating and Maintenance Instructions are supplied with each product and/or carton.

Provided it is installed correctly and receives adequate preventative maintenance it should give years of trouble –free service.

Abusive behaviour and accidental damage to the product are not covered by this guarantee.

The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or consequential damages.

SizePattern No.CodeBSI PB300 PB500 PB700 Ball ValvesWRAS PB300
15mmPB300T255021approved by BSI PB300 PB500 PB700 Ball Valvesapproved by WRAS PB300
22mmPB300T255022approved by BSI PB300 PB500 PB700 Ball Valvesapproved by WRAS PB300
28mmPB300T255023approved by BSI PB300 PB500 PB700 Ball Valvesapproved by WRAS PB300
DescriptionMinimum Operating
Pressure (bar)
Maximum Cold Working
Pressure (bar)
Maximum Hot
Working Pressure (bar)
PB300T Ball valveNo Minimum Operating Pressure16.0 bar at temperatures up to 30oC5.0 bar at temperatures up to 120oC

Care
No regular aesthetic care is required for this product

Maintenance
A regular maintenance program is the most efficient method of ensuring longer term operational efficiency of the selected valve. Such a program would need to include a risk assessment and a planned procedure of how the maintenance will be carried out. The possibility of operational limits being exceeded and the potential hazards ensuring must be considered as part of this assessment. This should be implemented to include visual checks on the valve’s condition and any development of unforeseen conditions, which could lead to failure. The correct fitting tools and equipment should be used for valve maintenance work. Separate means of draining the pipe work must be provided when carrying out any maintenance to valves. Where there may be any system debris this could be collected and /or filtered by installation of the appropriate protective device.

For further help please contact your local engineer.

If your product is under warranty please contact the Service Support Team on: 0800 1560050

Regulations
THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC and CE MARKING
The Pressure Equipment Regulations 1999 (SI 1999/2001) have now been introduced into United Kingdom law.

Valves with a maximum allowable pressure greater than 0.5 bar are covered by these new Regulations. Valves are categorised according to their maximum working pressure, size and rising level of hazard. The level of hazard varies according to the fluid being carried. Fluids are classified as Group 1, dangerous fluids or Group 2, all other fluids including steam. The Categories designated are SEP (sound engineering practice). Valves up to and including 25mm (1”) are designated SEP regardless of the fluid group. Those identified as having increased hazard are Categorised as, I, II, III or IV. All valves designated as SEP do not bear the CE mark nor require a Declaration of Conformity. Categories I, II, III or IV carry the CE mark and require a Declaration of Conformity. Valves classified from the piping chart would not be included in Category IV.

CE MARKING AND THE ATEX Directive 94/9/EC
cerning equipment and protection systems intended for use in potentially explosive atmospheres.

This has been implemented in United Kingdom law by the Equipment and Protective Systems Intended for Use in Potentially Explosive Atmosphere Regulations 1996(SI 1996/192) and amended by The Equipment and Protective Systems (amendment) Regulations 2001 (SI2001/3766).

The regulations apply to all valves where each valve:

  • has its own potential source of ignition.
  • operates in a potentially explosive atmosphere created by:

  • the presence of air/dust mixtures external to the valve.
  • The presence of gases, vapours, mists released from the valve through leakage.

The regulations will not apply to a valve without a potential source of ignition, which operates in a dust free environment and the fluid being transported is cold, inert gas or non –flammable liquid.

The requisite level of protection for valves not exempt from the regulations is defined as Group II category 2 and shall bear the following markings:

II 2 GD X

SizePattern No.CodePED Categorisation
15mmPB300T255021SEP
22mmPB300T255022SEP
28mmPB300T255023SEP
Pegler Yorkshire reserve the right to change specifications
ComponentMaterial
BodyForged Brass, Chrome Plated
End PieceForged Brass, Chrome Plated
BallBrass Bar, Chrome Plated (15mm) Forged Brass, Chrome Plated (22 to 28mm)
StemBrass Bar
SeatsPTFE (Teflon)
Thrust WasherPTFE (Teflon)
Stem O RingViton
Compression NutForged Brass, Chrome Plated
Compression ConeBrass
Yellow Tee HandleAluminium, Painted
Security ScrewNickel Plated Brass

You must sign in to your My PY account to access specification clauses

loading...
Remember me
 

Register for a My PY account

Please select the correct size

 

SteamWaterOilAirGas InertGas Combustible†Gas Corrosive††Gas Oxygen
yesyesyesyesyesyesyesno
Pegler Yorkshire reserve the right to change specifications

Gas application guide
Class 1. INERT Air, argon, carbon dioxide, helium, nitrogen
Class 2. COMBUSTIBLE Hydrogen, methane, natural gas, town gas
Class 3. CORROSIVE Chlorine, sulphur dioxide Class 4. OXYGEN
Class 1. INERT Air, argon, carbon dioxide, helium, nitrogen
† Valves are suitable for British Gas Applications Family Gases 1, 2 and 3.
†† Suitable in applications where moisture is completely absent.

Included in your data sheet will be: (Please uncheck the details not required)

General Information

Dimensions

Flow Data

Guarantee / Warranty

Approvals

Pressure & Temperature

Care & Maintenance

Installation Instructions

Regulations

Material Specifications

Spares

Technical Suitability

© 2019 Pegler. All Rights Reserved. Site Map  Social Media
Registered office: Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507
Legal: Privacy Policy  Cookie Policy  Modern Slavery Statement   Equal Opportunities  Terms & Conditions

PY Blog RSS twitter facebook link in youtube
Aalberts Industries